RPR Houston
  • Home
  • Jacketing
    • Sheet and Roll Jacketing >
      • Aluminum Jacketing
      • Stainless Steel Jacketing
      • Painted Jacketing >
        • Dura-Mate-70-hpc-tf
      • Aluminum Alclad
      • AZ-60
      • Galvanized Steel
    • Industrial Jacketing >
      • 1 1/4" Corrugated Sheets
      • 2.67" Corrugated Sheets
      • 4" Box Rib
      • 7.2 Rib Siding
      • Insul-Box Corrugated Sheets
  • Elbows & Tees
    • Aluminum Tees
    • Elbow Covers
    • Aluminum and Multi-Mate Size Chart for 90° Elbow Covers
    • Aluminum & Stainless Steel 316 Size Chart for 45 Elbows
    • Commercial Aluminum Fittings
    • Stainless Steel Size Chart for 90 Elbows
    • Short Radius Chart
    • Packaging Data - SS Elbow Covers
  • Fastening
    • Toggle Latch
    • Banding
    • Cut & Clip Banding
    • S&J Clips
    • White Steel Banding
    • Stainless Steel Closed Seals
    • Wing Seals
    • More Fastening Products
  • Add'l Products
    • Springs
    • Support Steel
    • Acoustical >
      • 1 # Mass Filled Vinyl
      • Acousti-Jac MFV
      • Acoustical Sheeting
    • Moisture Barriers
    • Tie Wire and Hex Netting
    • Melting Point
    • ARRA Compliance
    • Color Chart
    • Policy MSDS
    • More Products
  • Job Photographs
  • Contact Us
DOWNLOAD PDF

INSUL-MATE™
Insul-Springs

RPR INSUL-MATE™ COMPRESSION SPRINGS AND EXPANSION SPRINGS

​Insul-Mate
™ CS-6 Compression Springs are used with 3/4” x .020, .024 or .030 SS Strapping, and provide 80 lbs/inch of compression to accommodate the predictable expansion and contraction of large diameter insulated and jacketed tanks. The assembled component parts are manufactured from type 302, 304 and 316 (on special order) stainless steel. The springs hold tension on the system alleviating loose strapping on contraction cycles. Closed crimped seals are recommended.
Diameter: Wire - .125” OD, Spring - .935” OD
 
Insul-Mate™ CS-6 Super Compression Springs are used with 1 1/4” x .020, .024 or .030 SS Strapping, and provide 300 lbs/inch of compression. When tensioning the strapping, compress each unit a total of 1/2” and make sure tension is evenly distributed around the vessel. Closed crimped seals are recommended. 
Diameter: Wire - .162” OD, Spring - .935” OD    


Insul-Mate™ ES-7 Expansion Springs are heavy duty twin spring sets fabricated from T-302/T-304 stainless steel which allows for the predictable expansion and contraction of tanks, vessels, ducts, heat exchangers and other equipment. The spring set is 4.80” long with each of the two springs having a diameter of 0.695”. They are designed for use with 3/4” stainless steel strapping, .020, .024 or .030 thick. Closed crimped seals are recommended. 


Insul-Springs® are flat springs that allow for band expansion on large diameter vessels, pipes and tanks. Insul-Springs® are available in 4” lengths, 3/8” thick and 13/16” wide and are manufactured from T-302 Stainless Steel. The 4” spring is 4-3/8” long. 


Recommended for use over insulation under the jacketing system.








CORPORATE OFFICES & PLANT  |  RPR PRODUCTS, INC.  |  407 DELZ  |  HOUSTON, TEXAS 77018
sales@rprhouston.com | PHONE 713.697.7003 OR 1.800.231.0149  |  FAX 713.697.1844

Design by Houston Graphic Designer Jay Stevens
Website by Jay Stevens Design